![how to turn off a zone on a networx alarm pad how to turn off a zone on a networx alarm pad](http://www.cagroup.sg/wp-content/uploads/2019/02/full_K32LCD_2-e1550224008910.png)
And then so now that we have the main control panel selected, we just need to select the location within that. So, let's go ahead and hit 0, and then pound. So it says, "Enter device address." So, the majority of your programming is going to be done on device address 0, and 0, basically, just means the main control panel.
#How to turn off a zone on a networx alarm pad code#
So, now that we have a few basics done there, let's go ahead and go back into our main programming here which is *8, or by the installer code which is 9713. And so now, we're gonna scroll in through its screens, you can see Friday 2:30 p.m., January 5th.Īll right. And once you enter that all in, it automatically exits back out. It's the 5th, and it is January, and the year is '18. So, we'll just scroll to the 2, so, we're on 2:02 p.m., hit star, it goes to the minutes, which we'll now scroll up to get to 30, star again, it goes to the day. If you scroll up, it stays in the a.m., until you go around again. Now you can see it says, "12:02 a.m." Right now, it's about 2:30 p.m. It's going to say, "Please enter your code." And here, you'll just use the master code, default 1234. So instead of showing the time and date, it actually says, "Set clock *97." So, let's go ahead and hit *97. And you can see, it doesn't have any settings yet for the clock. The next thing that we're going to do is programming the clock. So again, we're gonna assign this keypad partition 1, and then push star.Īll right. It will be a lot of the same general steps but there are slight differences. In one, I can recover multiple partitions on this video. And again, most people are just gonna do one partition. So, we'll just make this keypad 1, and then star, and then the partition number. So here, you're going to enter the keypad number. So to do that, you're going to enter *94, and then your installer code. So that now we know that we're on a clean slate here, first thing you wanna do is assign the keypad number and partition. So, once you've completed the programming and the wiring, you're all done. So, that is all the programming that's required. This is for contact ID, which is what you wanna use for the bat unit. In here, you wanted to be on 13, it already is. So, the next thing that we'll do is go to device location 2. So here, I'm just entering 1234, and then pound. And again, the actual account number you entered doesn't matter, because it's not what is really going to be used by the bat. So, the next thing we need to do is enter an account number, and this is device location 1. So, once you have entered the phone number that you're going to enter, you'll just push pound. So, we're going to just enter a 10-digit number here, 1555555555. So, as long it dials out, we don't care what the number is. You just want the system to dial out but it's not actually dialing to something directly, it's just dialing to the bat. It doesn't really matter what you enter here. So here, you're just going to enter a fake phone number pretty much. So, the first thing we're going to do is go to location zero, which is for the phone number. And then you need a location followed by pound. So, we're going to use device address 0 and then pound. After you enter that, it's going to ask for the device address, then pound. To do that, you're gonna use *8 followed by the installer code. First thing you're gonna do is enter installer programming. So, let's go ahead and go to the table and we'll get started on the programming. And if you wait till the end of the video, I'll show you how you can get that. I'll be following more or less what we have in our Quickstart guide that we've written for you. There will be some obvious slight changes based on the number of zones and things like that. This video will apply to any of the network systems, the NX4, NX6, NX8.
![how to turn off a zone on a networx alarm pad how to turn off a zone on a networx alarm pad](https://www.homecontrols.com/homecontrols/images-sca/GENX148ERF_media-001.jpg)
In today's video, I'm going to be doing the basic programming for the Interlogix NetworX panels. Total Connect 2.0 Package Monitoring Add-OnsĪn extensive tutorial on programming the NX4, NX6, and NX8 Interlogix NetworX panels.Central Station Alarm Monitoring Services.